SNH120R46U12.1W21磨煤机润滑油泵

    三螺杆泵(SN三螺杆泵,sm三螺杆泵,spf三螺杆泵)选型时，要尽可能详尽地了解泵的使用条件，除运行参数，如流量、压力须要弄清楚之外，输送的介质的特性如介质的腐蚀性，含气量含固溶物的比率及固体颗粒的大小以及介质的工作温度、粘度、比重对泵内过流元件的腐蚀性等和泵装置的吸入条件，安装条件均要了解。Three-screw pump (SN three screw pump, three screw pump, sm SPF three screw pump selection, should understand the using condition of pump as much detail as possible, in addition to the operating parameters, such as flow rate, pressure need to figure out, transmission characteristics, such as corrosive medium, the medium of air content of solid solution and the ratio of the size of the solid particles as well as the working temperature, medium viscosity, specific gravity within the pump flow components of corrosive and pump suction conditions, such as the installation conditions are to understand.

   用户可以填写附在本样本后的泵数据表，由厂家负责选型，也可以根据样本按以下步骤自行选型。User can fill in the attached to this sample after pump data sheets, the manufacturer shall be responsible for the selection, can also according to the sample, follow these steps to selection.

   第一， 确定泵的转速：（SN 系列螺杆泵的极限转速为＜6000r.p.m）Determine the speed of the pump: (SN series screw pump limit speed for < 6000 r. p.)

   1．螺杆泵转速的选择以输送介质的粘度和泵的规格确定转速范围，一般输送高粘度介质时，螺杆泵应选低转速；若粘度低 ，相应选择高转速。The rotational speed of screw pump selection for medium viscosity and determine speed range of the specifications of the pump, transmission of high viscosity media in general, the screw pump should choose low speed;If the low viscosity, high speed accordingly.

   对于大规格的螺杆泵（主杆外径∮60mm 以上）For the large size of screw pump (more than 30 main stem diameter of 60 mm)

   介质粘度γ＞20°E 时，转速以970rpm 或720rpm 的螺杆泵。Medium viscosity gamma > 20 ° E, screw pump speed to 970 RPM and 720 RPM.

   若γ＞80°E 如粘胶液，转速可选n=200~500rpm的螺杆泵If gamma > 80 ° E, such as viscose, of optional n = 200 ~ 500 RPM of the screw pump

   对于小规格的螺杆泵（主杆外径∮60mm 以下）：For small specifications of the screw pump (below 30 main stem diameter of 60 mm) :

   γ＞20°E 时，n 选1450rpm 或970rpm的螺杆泵. Gamma > 20 ° E, n selected 1450 RPM and 970 RPM of screw pump.

   γ＞80°E 时，n 选300~600rpm的螺杆泵。Gamma > 80 ° E, n selected 300 ~ 600 RPM of the screw pump.

   2．由于螺杆泵的转速愈高摩擦功率愈高，螺杆泵的磨损越大，寿命越短，如果输送介质的润滑性较差，或含有微量杂质，应选较低转速，使泵保持较长的使用寿命。推荐n＜1450rpm。Friction due to the higher the rotational speed of screw pump power, the higher the wear and tear of screw pump, the greater the shorter life, if the medium of lubricity is poorer, or trace impurities, should choose a lower speed, to keep pump with long service life.The recommended n < 1450 RPM.

   第二， 结构形式的选择The choice of the form of structure

   结构的选择可根据螺杆泵的运行环境和安装环境，选择合适的安装形式并遵循以下的原则：On the choice of structure based on the operating conditions of a screw pump and the installation environment, choosing the appropriate type of installation and follow the following principles:

   1． 输送润滑性油类，且温度T＜80℃时，选择内置轴承结构的螺杆泵。1. Conveyor lubrication oil, and temperature T < 80 ℃, choose built-in bearing structure of the screw pump.

   2． 输送润滑性较差，或温度T＞80℃时，选择外置轴承结构的螺杆泵。2. The conveyor lubrication is poorer, or temperature T > 80 ℃, select external bearing structure of the screw pump.

   3． 输送流动性差，粘度高的介质或对所输送介质进行加热或保温时，选双层加热泵体结构的螺杆泵。3. Conveyor illiquid, high viscosity of the medium or the transport medium for heating or thermal insulation, choose double screw pump heat pump body structure.

   4． 输送高温介质时，应选择耐高温的材料制成的泵或局部冷却的螺杆泵。4. High temperature medium, high temperature resistant materials should be selected for the pump or cooling screw pump.

   5． 关于螺杆泵的吸入能力可查阅样本。5. About the screw pump suction capacity can refer to the samples.

   第三， 螺杆泵材料组合的选择 见上表Third, the choice of the screw pump material combination See the table above

   第四， 螺杆泵的吸上能力Fourth, the screw pump suction on ability

   通过降低转速或加热降低介质黏度的方法，可达到高的吸上性能，见NPSHR 表By reducing the speed or heating medium viscosity reduction methods, can achieve high on absorption performance, see the NPSHR table

   第五，配套电机的选配Fifth, motor selection

   螺杆泵的型号选定后，根据样本数据，可查到泵的轴功率N，该轴功率再加上一定的功率储备后，作为选配电机的依据，一般电机功率Nm 不小于泵轴功率N 乘以功率储备系数K 所得的值即：Nm≥K·N。K 值Screw pump model is selected, according to the sample data, the pump shaft power can be N, the shaft power plus the power of a certain reserve, as a basis for the matching machine, general motors power Nm not less than the pump shaft power N times the power reserve coefficient K of the proceeds of the value, namely: the Nm acuity k. N.K value

　　三螺杆泵能够在不同的行业中使用，在其中能够发挥重要的作用和性能，在行业中能够充分展现良好的性能优势，在产业性能中发挥重要的作用和贡献。下面从特点.困油及措施不平衡等方面向大家介绍一下三螺杆泵(3GR三螺杆泵,SNH三螺杆泵). Three screw pump can be used in different industries, in which can play an important role and performance, can fully show the good performance advantages in the industry, play an important role in industry performance and contribution.From below. Trapped oil and measures unbalance introduce three screw pump (3 gr three screw pump, three screw pump SNH).