电动污油泵,电动滑油泵,防爆树脂泵远东泵业

 尊敬的客户您好:

我们是河北远东泵业制造有限公司,公司已通过ISO9001：2000国际质量体系认证，中国船级社CCS型式认证，法国船级社BV产品工厂认证，美国船级社ABS产品质量认证，成为中石油物资资源市场成员、中石化物资资源市场成员，并列入《武器装备科研生产保密资格名录》可以承担军队系统装备部门的涉密武器装备科研生产合同项目。河北省知名产品生产企业，船用泵产品承制企业。我们的产品是：同样的价格我们的质量更优、同样的质量我们价格更低、同样的产品我们服务更好。

●KCB齿轮泵性能范围

　　主要用于油田、油库、港口、码头、船舶等大流量输油，卸油

　　应用范围:KCB/2CY型齿轮输油泵适用于输送粘度在300c.s.t以下的各种油类，如原油、柴油、润滑油、动植物油等。配用铜齿轮可输送低闪点液体，如汽油、苯等。介质温度不超过70℃，耐高温油泵的使用温度不超过300℃。本泵身带有安全阀，超载时起安全作用。轴封有骨架油封、机械密封、填料密封三种型式，订货注明。KCB齿轮润滑泵主要用于各种机械设备中的润滑系统中输送润滑油，适用于输送粘度在10oE（75c.s.t）以下，温度在300℃以下的具有润滑性的油料，不锈钢齿轮泵可输送食用油料、饮料等。轴封有骨架油封、机械密封、填料密封三种型式.

 ●KCB齿轮泵安装说明: KCB gear pump installation instructions:

　　1、安装泵的地点应足够宽敞，以方便检修工作。1, the location of the installation of pump should be spacious enough, to facilitate maintenance and repair work. The stand or fall of 2、泵安装的好坏，对泵的平稳运行和使用寿命有很重要的影响，所以安装校正工作必须仔细地进行，不得草率行事。2, pump installation, for the smooth running of the pump and service life have very important influence, so the installation calibration work must be carried out carefully and must not be too hasty. 3、泵吸入管的安装高度、长度和管径应满足计算值，力求简短，减少不必要的损失（如弯头等）；并保证泵在工作时，不超过其允许汽蚀余量。4、吸入和排出管路应该有支架。泵不允许承受管路的负荷。3, installation height of pump suction pipe, the length and diameter should satisfy the calculated value, to short, reduce unnecessary losses, such as elbow, etc.); And ensure the pump at work, no more than the allowed NPSH. 4, suction and discharge line should be a support. Pump are not allowed to bear load of pipeline.

●kcb齿轮泵安装: KCB gear pump installation:

　　1、泵安装前应检查泵和电机在运输过程中是否受到损坏，如电机是否受潮，泵的进出口防尘盖是否损坏而使污物进入泵腔内等。1, before the pump installation, should check the pump and motor is damaged during the transit, whether be affected with damp be affected with damp such as motor, pump the import and export of dust cover for damage and make the dirt into the pump chamber, etc.

　　2、泵在搬运过程中，应选择合适起吊位置，减少泵的变形。2, pump in the process of handling, should choose appropriate lifting position, reduce the deformation of the pump.

　　3、泵的底座应固定在牢固的基础上，以免产生振动影响泵的正常工作。3, the base of the pump should be fixed on the basis of the strong, so as to avoid vibration influence the normal work of the pump.

　　4、泵的进出口管路应清理干净不得存有硬颗粒的报告杂物。4, import and export of pipeline of pump should be cleaned up shall not have the report of hard particles sundry.

　　5、管路口径一般不小于泵的进出口径，进油管路应尽量短，并减少弯路。必要时在进油口安装金属过滤器，过滤器的有效面积不应小于管道过流面积的三倍。5, pipe diameter is generally not less than the in and out of the caliber of pump, the oil pipeline should be short, as far as possible and less detours.When necessary, metal filter is installed on oil inlet filter effective area should not be less than three times of pipe flow area.

　　6、安装时，不得用泵来承担管路的重量。7、用手转动联轴器，泵应转动灵活，不得有过紧或轻重不均现象，如有应立即排除。

6, when installation, must not use the pump to bear the weight of the line.7, turn the coupling with the hand, the pump should be flexible rotation, can not have too tight or weight uneven phenomenon, should immediately ruled out.