防火灾烟雾感应探测器光电式烟雾报警器外贸出口型AK-218B
信息编号:2574532 浏览:185次- 供应商
- 北京冠川科技有限公司 商铺
- 认证
- 报价
- 人民币¥38.00元每个
- 品牌
- gantch冠川
- 型号
- ak-218b
- 类型
- 烟雾探头感应器
- 所在地
- 北京市昌平区北七家镇高科技工业园
- 联系电话
- 84935219
- 联系人
- 张祥中 请说明来自顺企网,优惠更多
- 让卖家联系我
产品详细介绍
产品概述:
本产品为光电式感烟探测器(以下简称探测器)是采用烟雾中的颗粒折射红外光的原理探测火灾,电路主要由红外发射部分和接收部分组成,发射管与接收管置于光学迷宫中,光学迷宫可屏蔽外界杂散光的干扰,但不影响烟雾进入。在无烟状态下,接收管只接收到很弱的红外光,当有烟雾进入时,由于散射作用,接收到的光信号增强,当烟雾达到一定浓度时,控测器输出报警信号。为减少干扰及降低功耗,发射电路采用脉冲方式工作,可提高发射管使用寿命。产品具有防尘,防虫,抗外界光线干扰等功能,保证了产品的稳定性。本产品对缓慢阴燃或明燃产生的可见烟雾,有较好的反应。适用于住宅、商场、宾馆、饭店、办公楼、教学楼、银行以及仓库等室内环境的烟雾监测。
功能特点:
•••手动测试
•••自动复位
•••采用专用微处理器控制
•••防尘,防虫,抗白光干扰,环境适应性强
•••采用smt工艺制造,稳定性好
技术参数:
工作电压:dc12v(联网型)
静态电流:≤20ua (联网型)
报警电流:≤20ma
报警批示:红色led
报警声压:≥85db/m
工作温度:-10°c ~ +50°c
环境湿度:≤95 % rh
监测面积:25-40平方米
报警方式:继电器常开no/常闭nc (联网型)
发射距离:空旷距离100m(无线型)
执行标准:gb4715-1993
烟雾灵敏度:符合ul的217号标准
简易保养:
**每隔6个月便需清洁警报器一次以保持工作效率良好,先把电源关掉,再用软毛刷轻扫灰尘便可。再把电源启动。
若发现以下问题:
1、 按了测试健但不发声
2、烟雾测试但不发声
3、 预备灯不再稳定闪动
避免安装於以下位置:
1. 太接近门口,窗户,风扇等地方均会影响警报器的灵敏。因为这些地方一般空气流通较快。
2、 不可安装於高潮温度的地点,如浴室,顶楼或温度高於39ºc或低於5ºc。
注意事项:
1、本产品不宜安装在极冷极热、风速极高以及经常会有大量烟雾和灰尘存在的环境中。
2、产品每月进行一次测试。
3 为保证产品的感烟灵敏度,每隔六个月需要用软毛刷清洁探测器表面,清洁时必须先断开电源。
4、(独立型或无线型)当电池电压不足时,峰鸣器会每隔40秒发出短促的“嘀”声,为保证探测器的探测灵敏度,请及时更换电池。
5、如果发现产品不能正常工作,或者有损坏现象,请不要自行拆卸,可以联系客户服务中心或者Zui近的代理机构,将有专业人员为您服务。
6、光电感烟探测器可以减少灾难的发生,但不能确保万无一失。为了您的安全,请正确使用本产品,同时在日常生活中应提高警惕,加强安全防患意识。
product
introduction
this product named photoelectric detector(hereinafter called
detector) detects the smoke by a couple of infrared diodes. the
principle of detecting is granule in the smoke can reflect infrared
light. infrared diodes are placed in the special chamber. the
chamber can shield external light, but don't affect the smoke into
it. while have no smoke, the diode can receive very weak infrared
light. when the smoke entering the chamber, diode can receive more
and more light, when the smoke attains the certain density, the
detector can give out alarm signal. in order to reduce the
interference and lower power consumption, the emitting circuit
adopts the pulse signal. the detector adopts the special structure
design and asic, has the dustproof, mothproof and anti outside
light interference feature and etc. the detector is suitable for
detecting the smoke in house, shop, hotel, restaurant, office
building, school, bank, library, computer house, storehouse and
etc.
product profile
led
indicator
mounting base
product
feature
the detector has relay output n.c.and n.o.optional, it carries out
by changing the mini jumper location on the pcb. the
detector works once connected to dc power directly. led indicator
flashes every 9 seconds, when the detector work normally; when
alarms, led indicator is on, and the detector send out the
signal.
infrared photoelectronic sensor auto reset or reset by power off
intelligent logic control network output/ led indicating alarm
anti-light , mothproof , dustproof smt design, high stability
strong adaptability for circumstance
relay output
n.c.and n.o. optional stain steeless shield,anti-rfi(20v/m-1ghz)
technical specification
operating voltage dc 12v consumption current 15ma alarm indication:
red led on operating temperature: -10 +50
operating humidity : 95 rh anti-rfi: 10mhz-1ghz 20v/m
detecting area: 80 square meter(with the installation height of
6m-12m), and 60 square meter (with the installation height less
than 6m)
alarm output : relay output nc or no, dc28v, 100ma
reset mode: auto-reset or reset by power off
dimension size :104 mm dia.*51mm deep
sensitivity:i levelinstallation
1. connect the power line and signal line to the mounting base(1
for +12v contact, 2 for cathode, 3 and 4 for alarm
output contact )
2. select proper place (normally mounted on the center of the
ceiling) , fix the mounting base, then put the detector into
the base and turn it.
notice
1. the detector can not be installed under worse environment. e.g.
coldest, hottest, dusty, do not move away the
dustproof cover untill use the detector indeed.
2. make sure that there is no block within 0.5m from detector.
3. keep the distance between detector and source of wind flow more
than 1.5m.
4. keep the distance between detector and wall more than 0.5m.
5. make sure the distance between detectors be less than 15m. and
the distance between detector and corner must be less
than half of the one between detectors.
6. horizontally install the detector. if have to be installed
slantingly, please keep the angle less than 45 degrees)
7. please clean the detector by soft brush per six monthes to
ensure the sensitivity and life of product. pay attention to
switch off power before clean.
8. for various reason, including, but not limited to changes in
environmental conditions, electric disruptions and
tampering, the product may not perform as expected. the user is
advised to take all necessary precautions for his/her safety and
the protection of his/her property.
"供应防火灾烟雾感应探测器光电式烟雾报警器外贸出口型AK-218B"的工作电源为12DC,探测方式是光电式探测,环境温度为-20-+60(℃),报警电流是100mA,环境湿度为80(%),静态电流是30uA,类型为烟雾探头感应器,型号是AK-218B,使用范围为防火区域,适用范围是防火灾报警场所、家庭、办公室、仓库,品牌为Gantch冠川
- 诚招防盗报警,家用商用工程用有线无线报警主机,探测器代理加盟品牌:冠川
- 门窗磁防盗探测器磁开关3.50元/
工作电压:100VDC(V)