台湾平面钨钢磨盘 100*16
信息编号:589674 浏览:107次- 供应商
- 中山市盈易贸易有限公司 商铺
- 认证
- 报价
- 人民币¥10.00元每片
- 规格
- 100*16
- 类型
- 外圆磨砂轮
- 材质
- 钨刚
- 所在地
- 中山市小榄镇小榄大道南66号首层
- 联系电话
- 86 0760 22235298/22102237
- 手机号
- 13924962545
- 让卖家联系我
产品详细介绍
规格 | 100*16 | 类型 | 外圆磨砂轮 |
材质 | 钨刚 | 粒度 | 320(目) |
形状 | 平形砂轮 | 结合剂 | 其他 |
德国进口材料,台湾东升,产品锐利耐用
订购指南 精工细琢 专业品牌 | ||||||||||||
wa | 46 | k | 5 | v | 5 | a | 350x40x127 | |||||
磨料 | 粒度 | 结合剂 | 组织号 | 制法 | 型状 | 缘形 | 尺寸(dxtxh) | |||||
磨料粒度: | grit | |||||||||||
精度是用来表示磨料颗粒几何尺寸的大小,其选择 | grit is designated to represent the geometrical size of | |||||||||||
依据主要是加工工件所需要的表面粗糙度,同时也需 | abrasive grain.the grit size is chosen for customer"s | |||||||||||
考虑其他一些因素.以外圆磨为例,常用粒度与表面 | required surface finish as well as other conditions.for | |||||||||||
糙度有下面的大致关系: | example,in cylindricai grinding,there is relationship | |||||||||||
between grit and surface finishes listed as bellow; | ||||||||||||
粒度 | 36-46 | 54-60 | 70-80 | 90-100 | grit | 36-46 | 54-60 | 70-80 | 90-100 | |||
粗糙度 | ra 1.6 | ra 0.8 | ra 0.4 | ra 0.2 | finish | ra 1.6 | ra 0.8 | ra 0.4 | ra 0.2 | |||
●粗料度的磨料适用于磨削: | ●use coarse grit: | |||||||||||
1)材质较软,延伸率大以及类似软铁和有色金属等 | 1.for soft,ductile,stringy material such as softsteel | |||||||||||
材料 | and nonferrous material | |||||||||||
2)进给量大,磨削速度要求高的场合. | 2.for rapid stock removal,high grinding speed | |||||||||||
3)表面粗糙度要求不高的场合. | 3.where finish is not important | |||||||||||
4)磨削接触面大的场合. | 4.for large areas of contact | |||||||||||
●细粒度的磨料适用于磨削: | ●use fine grit: | |||||||||||
1)硬度较高以及类似高碳工具钢,硬质合金钱类的金 | 1.for hard,brittle materials such as hard tool steels, | |||||||||||
属材料和玻璃等脆性材料. | cemented carbide and glass. | |||||||||||
2)表面粗糙度及精度要求高的场合. | 2.for fine finishes | |||||||||||
3)磨削接触面小的确场合. | 3.for small areas of contact | |||||||||||
4)工件半径或弧度小的场合. | 4.for holding small corner radii | |||||||||||
硬度: | grade: | |||||||||||
e f g h i j k l m n o p q r | e f g h i j k l m n o p q r | |||||||||||
软----------------------硬 | soft------------------hard | |||||||||||
砂轮的硬度是指磨料之间的结合度,砂轮中结合 | the grade indicates the relative holding power of the | |||||||||||
剂量的多少决定了砂轮的硬度大小.用户需根据具 | bond which holds abrasive grains in a wheel.ln general, | |||||||||||
本的磨削(如进刀量,粗糙度,材质)要求来灵活选 | with a given type of bond it is the mount of bond which | |||||||||||
择砂轮的硬度. | determines a wheel"s should select the grade of a wheel | |||||||||||
一般砂轮硬度选择的原则是: | based on the grinding parameters such as feed rate. | |||||||||||
finish requirements,materiials i.e..the following rules | ||||||||||||
should be followed with regard to grade | ||||||||||||
●较软的硬度 | ●use soft grade: | |||||||||||
1)进刀量大的粗磨. | 1.for rapid stock removal | |||||||||||
2)磨削接触面大的场合. | 2.for large greas of contact | |||||||||||
3)材质较硬的工件,如高硬度工具钢和硬质合金钢等. | 3.for hard materials such as hard tool steels and carbide. | |||||||||||
4)工件抗热性能差,严防表面烧伤和磨削. | 4.for heat sensitive workpieces and grinding can not has | |||||||||||
burning and discoloration on surface | ||||||||||||
●较硬的硬度 | ●use hard grade: | |||||||||||
1)进刀量小的精磨. | 1.for fine finish with little feed | |||||||||||
2)延长砂轮寿命. | 2.for longer wheel life | |||||||||||
3)材质较软的工件. | 3.for soft materials | |||||||||||
4)磨削接触面小或窄的场合. | 4.for small or narrow areas of contact | |||||||||||
组织号: 5 6 7 8 9 10 11 12 13 | structure: | 5 6 7 8 9 10 11 12 13 | ||||||||||
密--------------- 疏 | close------------open | |||||||||||
组织号用以表示砂轮内相邻的磨料颗粒之间的距 | the structure number indicates the space between neighboring | |||||||||||
离也就是间隙的大小.砂轮中磨料颗粒所占的体积百 | grains which can also be called grain spacing in a wheel the | |||||||||||
分比,也就是其浓度的大小,决定的砂轮的组织号.陶 | volume percentage of abrasive grains which represents the | |||||||||||
瓷砂轮组织号变化范围一般是从5到13,数字越小表 | density of grain in a wheel determines the structure number | |||||||||||
示砂轮组织越密,数字越大表示砂轮组织越疏松.组 | of a wheel.the structure of vitrified sheels ranges from 5 to | |||||||||||
织11,12和13通常是指气孔砂轮. | 13.the smaller the number,the more closed structure the wheel | |||||||||||
the large the number,the more open structure wheel the numbers | ||||||||||||
11.12.13normally indicate porous wheels. |
我们的其他产品
- 绒布砂纸 BIG 多款供选5.00元/PCS
型号:BIG - 进口TTK铣刀 样品 标准件200.00元/支
样品或现货:样品 - CTL-2TL铣刀 样品80.00元/支
样品或现货:样品 - 进口CEM-4TL铣刀 样品80.00元/支
样品或现货:样品 - CER-2TL铣刀 样品80.00元/支
样品或现货:样品 - 台湾东升平面不织布砂轮 100*10*169.00元/片
规格:100*10*16 - 台湾东升平面海棉砂轮 100*10*166.00元/片
规格:100*10*16 - 台湾东升可弯曲砂轮 多款供选6.00元/片
规格:100*2.5*16 - 东升平面砂布轮 100*166.00元/片
规格:100*16 - 台湾立式平面砂布轮 100*166.00元/片
规格:100*16