油脂输送泵用NYP高粘度泵效果好

●高粘度泵的工作压力的选定

　　1, select the work pressure

　　高粘度泵额定的压力是指泵连续工作时的Zui高许用压力，而其工作压力则决定于外部负载，安装和调试的寿命与其工作压力直接相关。对于不频繁工作的齿轮泵，其工作压力可取为泵的额定压力，考虑到产品质量不同，将额定压力降低20%～30%使用。对于经常工作于较高压力下的齿轮泵，其工作压力应比泵的额定压力低1～2个压力级。石油化工设备常常是24小时连续运转，这时泵的工作压力应该取得比额定压力低得多，且工作转速也应该低于额定转速。如果高粘度齿轮泵的工作压力调整过高，则会使齿轮泵在超负荷下运行。High viscosity pump rated pressure refers to the maximum allowable pump continuous work pressure, and its working pressure is determined by the external load, installation and commissioning of life is directly related with work pressure.For not frequent work gear pump, the working pressure is desirable for the rated pressure of the pump, taking the into consideration, it is best to used pressure rated lower 20% ~ 30%.For often work under high pressure gear pump, the working pressure shall be lower than the rated pressure of the pump 1 ~ 2 pressure level.Petrochemical e are often 24 hours of continuous operation, and at this time of the pump working pressure should be obtained was much lower than the rated pressure, and the work speed should be lower than the rated speed.If the high viscosity gear pump high pressure adjustment, will make the pump running under overload.

●NYP高粘度泵的安装与试运转

　　Installation and commissioning

　　高粘度泵的支座或法兰与其驱动电机应采用共同的安装基础，基础、法兰或支座均需具有足够的刚度，以减小齿轮泵运转时产生的振动和噪声。电动机与齿轮泵须用弹性联轴器连接，同轴度小于0.1毫米，倾斜角不得大于1度。安装联轴器时不得用锤敲打，以免伤害齿轮泵的齿轮等零件。若用带轮、链轮等驱动时应设托架支承，以防主动齿轮轴承受径向力。紧固齿轮泵、电动机的地脚螺钉时，螺钉受力应均匀，连接可靠。用手转动联轴器时，应感觉到齿轮泵能够轻松地转动，没有卡紧等异常现象出现，然后才可以配管。高粘度齿轮泵的吸油管道内径应足够大，并避免狭窄通道或急剧拐弯、弯头，去除不必要的阀门、附件，尽可能地降低泵的安装高度，缩短吸油管道的长度，以减少压力损失。管接头等元件的密封要良好，以防止空气侵入，从而控制气穴与气蚀的发生。在开始运转前，往齿轮泵的壳体内灌满待输送的液体，便于安全动。若环境温度低于冰点，应预先向泵内通入热蒸汽，进行预热处理，然后才可启动齿轮泵。齿轮泵的旋转方向要与进、出油口相符。齿轮泵若是第一次运行，或长期闲置后再使用，在空载或小负荷情况下先跑合一小时左右。如果在跑合阶段预先觉出异常温升、泄漏、振动和噪声时，应机检查。高粘度泵的出口管路上还应当设置安全阀等保护装置，这样一旦泵的出口通道发生堵塞，就可以打开安全阀卸压。对于需要正反转的高粘度齿轮泵，其进出口管路上均需设置安全阀。High viscosity pump bearing or flange and its drive motor should use common installation basis, foundation, flange or support all needs to have enough rigidity, to reduce the vibration of gear pump is running and noise.Motor and gear pump with elastic shaft coupling, coaxial degree is less than 0.1 mm, Angle shall not be greater than 1 degree.When installing coupling hammer shall not be used, in order to avoid damage gear and other parts of the gear pump.If use the belt wheel, wheel, etc, shall set bracket support, in case of driving gear bearing by the radial force.Ground screw fastening gear pump, motor, screw force should be uniform, reliable connection.Turn the coupling with the hand, should feel can easily turn the gear pump, no abnormal phenomenon such as clamping, then can be piping.High viscosity gear pump oil suction pipe diameter should be large enough, and to avoid the narrow channel, or a sharp bend, bend, remove unnecessary valves, fittings, as much as possible to reduce the installation height of pump, shorten the length of the oil suction pipe, in order to reduce the pressure loss.Components, such as pipe joint sealed well, in order to prevent the air intrusion, thus control air-pocket and the occurrence of cavitation.Before starting operation, to gear pump casing filled with liquid, easy to safety.If the environment temperature is below freezing, should advance to pump into the hot steam, preheating treatment, and then to start the pump.Direction of rotation of the gear pump, oil outlet in accord.Gear pump is the first run, or long-term idle before using, had better under the condition of no load or small load to run one hour or so.If in the running-in stage in advance the abnormal temperature rise, leakage, vibration and noise, should machine inspection.High viscosity of the pump outlet pipe also shall set up relief valve or other protective device on the road, so that once the clogging pump export channels, can open the relief valve pressure relief.For high viscosity gear pump need positive &negative, import and export all needs to set up the line safety valve.

●高粘度泵如何选型How to choice

    选择高粘度泵时应该注意泵所输送的具体粘度、工作温度、介质比重、介质成分等等，只有更好的了解高粘度泵所输送的介质情况才能更好的选择所需要的高粘度泵产品。

Should be paid attention to when selecting high viscosity pump pump delivery by the specific viscosity, working temperature, the proportion of medium, medium composition etc., only a better understanding of the high viscosity pump transmission medium condition can better choose the required high viscosity pump product.

　　必须了解高粘度泵所输送的介质粘度。因为介质粘度的高低直接影响到选择高粘度泵的转速。must understand the high viscosity pump transmission medium viscosity. Because the medium viscosity directly affects the choice of high viscosity pump speed.

　　了解高粘度泵所输送介质的性质，例如有没有腐蚀性。understand the nature of the high viscosity pump conveying medium, such as corrosive.

　　高粘度泵所输送的介质浓度多少、比重多少。 high viscosity pump how far the conveying medium concentration, specific gravity.

Fourth,

　　高粘度泵所输送的介质。high viscosity pump transmission medium.

　　高粘度泵输送的介质常温下是否结晶或凝固。the high viscosity pump whether the medium temperature of crystallization or coagulation.

　　高粘度泵所输送的介质是否有悬浮物。the transmission medium for high viscosity pump suspension.

　　高粘度泵所输送介质受温度变化情况。high viscosity pump conveying medium affected by temperature changes.

　　高粘度泵所输送介质的润滑性、清洁度、腐蚀性等。high viscosity pump medium by lubricity, cleanliness, corrosion resistance, etc.

　　高粘度泵要求进口压力及出口压力和安装高度。 high viscosity pump inlet pressure and outlet pressure and the installation height.

　　高粘度泵使用场合的防爆要求。high viscosity pump occasions of explosion-proof re    河北远东泵业制造有限公司坐落于铸造名乡—河北省泊头市。公司占地面积38650平方米，建筑面积20300平方米，是国内的集设计、铸造、生产、销售、服务于一体的容积泵专业制造厂家。公司始建于1984年,有二十几年专业研制经验。目前产品设计采用国际先进水平实体设计软件；产品研发、制造、检验、交付按照ISO9001质量管理体系控制过程质量；产品制造广泛使用加工中心、数控机床、专用精机、高精设备；检测设备拥有工具显微镜、渐开线检测仪、光学投影仪、测齿仪、脉冲辉光离子氮化炉等大型检测设备，并建有国家B级试验站。本厂以的产品水平、优质的售后服务、恪守信用而在市场上倍受欢迎，产品畅销不衰，赢得了用户的普遍赞誉。公司已通过ISO9001：2000国际质量体系认证，中国船级社CCS型式认证，法国船级社BV产品工厂认证，美国船级社ABS产品质量认证，中国渔业船舶检验局船用泵认证,成为中石油物资资源市场成员、中石化物资资源市场成员。河北省知名产品生产企业，船用泵产品承制企业。Hebei far east pump industry manufacturing co., LTD is located in botou city, hebei province, a casting of the township.The company covers an area of 38650 square meters, construction area of 20300 square meters, is the domestic famous design, casting, production, sales and service in one of the positive displacement pump professional manufacturer.Company was founded in 1984, has 20 years experience in professional development.The current product design adopts the international advanced level entity design software;Product research and development, manufacture, inspection, delivery, in accordance with the ISO9001 management system of process control;Widely used products manufacturing processing center, numerical control machine tools, precision machine, high precision e;Testing e has universal tool microscope, involute tester, optical projector, universal gear tester, pulse glow ion nitriding furnace and other large-scale testing e, and built national B level test station.The factory with the first-class products, excellent after-sales service, abide by credit and popular in the market, the products sell well and win the user's universal praise.The company has passed ISO9001:2000 international system certification, China classification society CCS type approval, bureau veritas BV products factory certification, the United States classification society ABS product certification, China's Marine fishing vessel inspection bureau pump certification, has been a member of the material resource market in oil, sinopec material resources market member.Well-known products production enterprise in hebei province, Marine pump products enterprises.

    公司以“泊远东”牌齿轮泵，螺杆泵为主导产品，涉及21个系列，4200多种规格，年生产能力达43000多台（套）。产品行销油田、化工、电力、船舶、冶金、食品等各大行业。产品除满足国内客商的需求外，部分出口至东南亚、美洲、欧洲等国家和地区。公司在全国各大城市设有30多个分支机构，并建立了完善的营销服务网络，拥有一支庞大敬业的营销服务队伍，可为广大客户提供优质的服务。 公司以严谨的质量体系、先进的生产设备、完善的检测手段、丰富的制造经验、务真求实的远东团队，来有效保证产品质量。以满腔真诚期待与国内外各界人士携手铸就多方共赢的。Company to "moored far east" brand gear pump, screw pump for the leading product, involves the 21 series, more than 4200 kinds of specifications, annual production capacity of more than 43000 Taiwan (sets).Product marketing oilfield, chemical industry, electric power, shipbuilding, metallurgy, food and other major industry.Products in addition to meet the needs of domestic customers, some exports to southeast Asia, the americas, Europe and other countries and regions.The company has more than 30 branches in major cities throughout the country, and established a perfect marketing service network, has a large professional marketing services team, can provide the high service for the customers.Companies with strict system, advanced production e, perfect detection means, rich manufacturing experience and WuZhen strives for the far east team, to effectively ensure the of products.To sincerely look forward to working with people from all walks of life both at home and abroad hand in hand to own a bright multi-win-win situation.

    我公司是一个生产齿轮油泵和螺杆泵的专业公司。公司拥有各种设备80台,主要设备有：C6140  CW6163C车床24台，TX611C/4镗床2台，M131M7130磨床8台，C125A立车2台，Y318K Y3150E滚齿机6台，E3050X16/1摇臂钻床2台，E5163立式钻床2台，B1-400铣床3台，螺杆泵转子专用铣床1台，半自动螺旋转子铣床2台，X53K立铣3台，半自动螺旋转子 磨刃机台。My company is a company specialized in the production of gear oil pump and screw pump.Company has 80 sets of various devices, the main e are: C6140 CW6163C 24 sets of lathe, TX611C/boring machine 2 units, 4 M131M7130 grinding machine 8 units, C125A set, 2 sets, Y318K Y3150E hobbing machine 6 units, E3050X16/1 radial drilling machine 2 sets, E5163 vertical drilling machine 2 sets, B1-400 universal milling machine 3 units, screw pump rotor 1 milling machine, semi-automatic screw rotor - b milling machine 2 sets, X53K three vertical milling, semi-automatic screw rotor QH2 -031 edge grinding machine is used.

    我公司拥有省计量局制试验台1台，自制试验台3台，使生产产品从原材料投入到产成品出厂实现了全过程检测。产品出厂合格率 ，具备较强的综合配套制造能力。理化试验室、长度计量室是国家计量确认合格单位，使产品从原材料投入到产成品出厂实现了全过程检测。产品出厂合格率 ，具备较强的综合配套制造能力，公司年可生产各种泵 6000 多台。My company has the province system test bench 1 bureau of standard measurement, homemade test-bed 3 units, production of products from raw materials into finished goods factory implements the whole process of detection.Product factory rate , have strong ability of comprehensive manufacturing.Physical and chemical laboratory, length measuring room is the national metrological confirmation unit, make our products from raw materials into finished goods factory implements the whole process of detection.Product factory rate , have strong comprehensive manufacturing capacity, company can produce all kinds of pump in more than 6000 units.

运费说明:

    1.本公司常规产品1-3天发货,特殊要求或者需定做的产品发货时间已与客户协商为准, 2.泵运费方式有两种:快递和物流.小泵和小型配件发快递,其余体积较大,数量较多,推荐走专线物流货运,一般南方,中部地区及沿海地区3-5天左右到达.西部,北部较远的地区以及少数二次中转地区5-8天左右可到,具体覆盖范围请咨询公司客服人员.安装使用:请您根据产品说明书的步骤进行操作,如有问题,请联系我公司,我公司将会请Zui专业的技术人员为您提供服务.为了保护您的利益,我们已经提醒客户在收到货物时,要开箱验货,如在打开验货时发现货物丢失,损害或者不符,请拒绝签收,您签收就代表已准确无误的收到后屋,若在签收货物之后才发现货物丢失或者不符,如不负责. 客户收到货后,产品无法安装或者规格有误,本公司提供退货或者换货服务,退货或者换货的客户请保证货物的完好无损,并承担往返运费. 客户收到后,如果产品存在质量问题,请在收货后7天内联系我公司,提供相关质量问题图片,我公司将在第一时间给您退货或者换货,因为我公司已经在发货前已经仔细检查过,所以过期将不提供此项服务,还请谅解.S