贴片连接器、1.25立式贴片连接器4-18P
信息编号:2887380 浏览:369次- 供应商
- 深圳市德瑞电子有限公司 商铺
- 认证
- 报价
- 请来电询价
- 品牌
- MSTCONN
- 型号
- 1.25-C-NP
- 所在地
- 深圳市宝安区松岗街道广深路480号
- 联系电话
- 13802206789
- 手机号
- 13723739518
- 董事
- 幸坤新 请说明来自顺企网,优惠更多
- 让卖家联系我
产品详细介绍
产品规格书
product specification【1】适用范围 scope
本规格书适用于:1.0间距柔性扁平电缆连接器(有锁式)
this specification covers the 1.0mmpitch fpc/ffc connectors(series locking)
【2】产品名称及型号 product name and part number
产品名称product name |
产品型号part number |
ffc/fpc扁平电缆连接器 |
|
|
|
【3】定格 ratings
项目item |
规 格 requirement |
||
Zui大容许电压 rated voltage(max) |
50v |
[ac/dc(有效值 virtual value)50hz] |
|
Zui大容许电流 rated current(max) |
0.4a |
||
使用温度范围 ambienttemperature range |
-25℃~ +85℃ |
||
【4】性能 performance
4.1电气性能 electrical performance
项目item |
条件 test condition |
规格requirement |
|
4.1.1 |
接触电阻 contact resistance |
适合fpc/ffc嵌合;开放电压20mv以下;短路电流10ma的状态下测定。 mate applicable fpc/ffc and measure by dry circuit,20mv max,10ma. |
≤20 mωmax |
4.1.2 |
绝缘电阻 insulation resistance |
适合fpc/ffc嵌合;相邻端子间或端子与地面间加dc 500v下测定。 mate applicable fpc/ffc and apply 500v dc between adjacent terminal or ground. |
500mωmin |
4.1.3 |
耐电压 dielectric |
适合fpc/ffc嵌合;相邻端子间或端子与地面间加ac 200v(有效值)历时1分钟下测定。 mate applicable fpc/ffc and apply 200v ac(virtual value)for 1minute between adjacent terminal or ground. |
无击穿现象 no breakdown |
4.2机械性能 mechanical performance
项目item |
条件 test condition |
规格requirement |
|
4.2.1 |
锁紧力及拔出力 locking and withdrawal force |
适合0.3mm厚的ffc;用每分钟25±3mm的速度;平行地插入、锁紧、拔出。 insert and extract applicable ffc at the speed rate of 25±3mm/minute. |
锁紧力locking 1.96*n (n) max 拔出力withdrawal 0.49*n (n) min |
4.2.2 |
端子保持力 terminal /housing retention force |
以用每分钟25±3mm的速度平行向外拉 pull the terminal at the speed rate of 25±3mm per minute |
3.92n min |
4.3环境和其他性能 environmental performance and others
项目item |
条件 test condition |
规格requirement |
||
4.3.1 |
重复插拔 repeated insertion and withdrawal |
无通电状态;以10次/分钟的速度插拔20次 insertion and withdrawal actuator up to 20 cycles at the speed rate of less than 10 cycles/minute |
接触抵抗 contact resistance |
60 mωmax |
4.3.2 |
温度上升 temperature rise |
适合fpc/ffc嵌合;Zui大容许电流通电,温度测定。(ul 498) carrying rated current load.(ul 498) |
温度上升 temperature rise |
30℃max |
项目item |
条件 test condition |
规格requirement |
||
4.3.3 |
耐振动性 vibration |
dc 1ma通电状态下;嵌合轴沿xyz三个方向振动;振幅1.5mm;频率10-55-10hz/分;历时2小时 amplitude:1.5mm p-p sweep time:10-55-10hz in 1 minute duration:2 hours in each x.y.z. axes |
外观 appearance |
无损坏 no damage |
接触抵抗 contact resistance |
60 mωmax |
|||
瞬断 discontinuity |
1 ms max. |
|||
4.3.4 |
耐冲击性 shock |
dc 1ma通电状态下;嵌合轴沿相互垂直的6个方向;以490m/s2{50g}冲击;各3次 490m/s2{50g},3 strokes in each x.y.z. axes. |
外观 appearance |
无损坏 no damage |
瞬断 discontinuity |
1 ms max. |
|||
4.3.5 |
耐热性 heat resistance |
适合fpc/ffc嵌合;85±2℃的空气中;放置96小时;再回到室温中放置1-2小时 85±2℃,96 hour |
外观 appearance |
无损坏 no damage |
接触抵抗 contact resistance |
60 mωmax |
|||
4.3.6 |
耐寒性 cold resistance |
适合fpc/ffc嵌合;-40±2℃的空气中;放置96小时;再回到室温中放置1-2小时 -40±2℃,96 hour |
外观 appearance |
无损坏 no damage |
接触抵抗 contact resistance |
60 mωmax |
|||
4.3.7 |
耐湿性 humidity |
适合fpc/ffc嵌合;40±2℃、相对湿度90-95%的空气中;放置96小时;再回到室温中0.5小时内测定
temperature:40±2℃ relative humidity:90-95% duration:96 hours |
外观 appearance |
无损坏 no damage |
接触抵抗 contact resistance |
60 mωmax |
|||
耐电压 dielectric strength |
必须满足4.1.3 must meet 4.1.3 |
|||
绝缘抵抗 insulation resistance |
20 mωmin |
|||
4.3.8 |
温度循环 temperature cycling |
适合fpc/ffc嵌合;-55±3℃ 30分钟;常温常湿 10-15分钟;85±2℃ 30分钟;常温常湿 10-15分钟,循环5次。 5 cycles of: a) -55±3℃ 30 minutes b) 85±2℃ 30 minutes |
外观 appearance |
无损坏 no damage |
接触抵抗 contact resistance |
60 mωmax |
项目item |
条件 test condition |
规格requirement |
||
4.3.9 |
耐盐雾性 salt spray |
适合fpc/ffc嵌合;35±2℃、5±1%的盐水喷雾48小时;试验后常温水洗;再室温干燥。 48±4 hours exposure to a salt spray from the 5±1% solution at 35±2℃. |
外观 appearance |
无损坏、腐蚀 no damage |
接触抵抗 contact resistance |
60 mωmax |
|||
4.3.10 |
耐亚硫酸 so2 gas |
适合fpc/ffc嵌合;40±2℃、50±5ppm的亚硫酸中放置24小时 24 hours exposure to 50±5ppm. so2 gas at 40±2℃. |
接触抵抗 contact resistance |
60 mωmax |
4.3.11 |
耐氨性 nh3 gas |
适合fpc/ffc嵌合;浓度为28%的氨水容器中;放置40分钟。 40 minutes exposure to nh3 gas evaporating from 28% ammonia solution |
外观 appearance |
无损坏 no damage |
接触抵抗 contact resistance |
60 mωmax |
|||
4.3.12 |
可焊性 solder ability |
端子前端基准面0.2mm处浸入235±5℃的锡槽中;历时2±0.5 sec。 soldering time:2±0.5 sec. soldering temperature:235±5℃ 0.2 mm from terminal tip |
沾敷性 solder wetting |
沾敷面积95%以上
|
4.3.13 |
耐焊接热 resistance to soldering heat |
端子前端基准面0.2mm处浸入260±5℃的锡槽中;历时5±0.5 sec。 soldering time:5±0.5 sec. soldering temperature:260±5℃ 0.2 mm from terminal tip |
外观 appearance |
无损坏、变形 no damage |
本产品的加工定制是否,品牌是MSTCONN,型号是1.25-C-NP,应用范围是PCB,种类是FFC/FPC,接口类型是ZIF,形状是条形,制作工艺是冷压,特性是阻火/阻燃,工作频率是低频,接触件材质是磷青铜,绝缘体材质是LCP,芯数是4-18P
- FPC连接器,条形连接器
- FFC连接器、1.0抽拉卧式下接触连接器4-18P品牌:MSTCONN
- FPC连接器、0.5mm翻盖式连接器22P加工定制:否