氯化橡胶防腐漆 沈阳工业漆 沈阳防锈漆 沈阳防腐漆

沈阳信利涂料有限公司

shenyangxinli coating co.ltd

型号(type).........................................

dcj-0661

规格(standard).....................................

组成(composition)..................................

由氯化橡胶、颜料、体质颜料、助剂和有机溶剂调制而成。
mixed up with chlorinated rubber, pigment, corporeity pigment, additive and organic solvent.

性能及用途(capacity&application).....................

漆膜具有良好的附着力和耐水性，防锈性能突出，更具有一次涂膜厚等特点。广泛应用于船舶、桥梁和大型金属结构的防锈底漆。
good adhesion and water-proofing property, outstanding anticorrosion performance, even the specialty of once-coating thick. widely used as the antirust primer of ships, bridges and large-scale metal structures.

施工参数[application parameter]......................

颜色(color) .........................................

红、灰、黑
brown 、red lead and grey

平均密度(mean density) ..............................

1.46g/ml

原漆粘度(primary paint viscosity) ......................

（25℃）77－87ku

涂装道数(application thickness).......................

1－ 2 道; 1-2 lines

理论涂布面积(theoretic painting area)..................

4－7m2/kg

一道漆腊厚度(first painting thickness).................

湿膜厚度约170 μm 干膜厚度约70 μm;wet film thickness:170 μm, dry film 70 μm

干燥时间(drying time)...............................

（25℃）表干≤1h 实干≤7h;（25℃）, surface drying≤1h, whole drying≤7h

涂装间隔(painting distance)...........................

（25℃）Zui低限度9 h Zui高限度 无限时;（25℃）, 9h is the minimum and without the maximum

稀释剂(thinner)......................................

名称 氯化橡胶漆稀释剂　　稀释量0－5％（按重量）
name:thinner for chlorinated rubber paint
thinning quantity: 0-5% (according to the weight)

施工方式(application mode)...........................

无气喷涂；刷涂；滚涂;无气喷涂(喷嘴型号:graco 163- 719 721) 喷出压力：4-6kg/cm2
gasless spray , brush , roller coating ;airless sprayt he type of gun mouth :graco 163-719 721;spray spress :4-6kg/cm2

参考施工粘度(referenced application viscosity) ........

无气喷涂120s ；刷涂60－80s ；滚涂60－80s ;无气喷涂(喷嘴型号:graco 163- 719 721) 喷出压力：4-6kg/cm2
gasless spray for 120s, brush for 60-80s, roller coating for 60-80s;airless sprayt he type of gun mouth :graco 163-719 721;spray spress :4-6kg/cm2

表面处理(surface treatment)..........................

抛丸及喷砂除锈，使其达到标准sa2.5级，或用动力工具使其达到标准st3级，除去表面油污 、水分及杂质等。
impact cleaning and sandblasting to remove the rust in order to reach level sa2.5, or reach sa3 with power tools and get rid of the surface smear, moisture and dust etc.

施工条件(application conditions).......................

为避免水汽凝结，要求温度在较露点以上，相对湿度低于80％，干燥期间应保持良好通风。
in order to avoid the steam from concreting, the temperature should be above zero centigrade and the relative humidity should be lower than 80%, good aeration in course of drying.

配套涂层(painting corollary coating)....

前道配套涂层： 环氧富锌底漆等
后道配套涂层：氯化橡胶面漆
previous corollary coating: epoxy zinc primer
latter corollary coating: chlorinated rubber top-coat

贮存期(life)..........................................

12个月; 12 months

包装(packing)........................................

单罐制包装
single tin

安全(safety) .........................................

应在通风良好处喷涂，必要时采取适当的安全防护措施，注意防火。
spray in places with good aeration conditions and take relevant safety measures if necessary. pay attention to
fireproofing.

责任声明(responsibility announcement)................

上述产品施工指南中所载的资料，只能作为使用的指南，任何人如使用本产品自定用途，须事前向本厂查询其适用于否，否则其一切功效与损耗，本厂将不负责任。此指南所载的资料，可因本厂产品不断发展和经验积累而随时更改。
the data here can be used only as the using guidance, anyone who wants to use our product for special using must query us for that, otherwise we are not responsible for
any subsequently effect and damage. the data in the guidance can be changed with our products’ development and our experience’s accumulation.