品牌	国产	型号	G07RC01
应用范围	发光模组	结构	点接触型
材料	磷铟砷化镓GaAsInP	封装形式	直插型
封装材料	树脂封装	功率特性	小功率
频率特性	低频	发光颜色	红色
LED封装	无色透明封装(T)	出光面特征	三角形
发光强度角分布	散射型	正向直流电流IF	20（A）
最高反向电压	8（V）

专业制造，长期稳定供货，有现货，保质量，同类产品最优价格

特征：高亮度，大发光角度

主要应用范围：发光模组

详细参数参阅以下说明书

product specifications

type : 7mm piranha red led

part number: g07rc01

lens color: water clear

● features:

1．long operating life

2．instant light

3．low voltage operated

4．cool beam,safe to the touch

5．more energy efficient than incandescent and most halogen lamps

6．widely used in the lighting , industrial and electronics products.

● package outline dimension:

notes:

1、 all dimensions are in millimeters；

2、 tolerances are ±0.1mm,unless otherwise noted.

● typical electrical & optical characteristics (ta=25℃)

part number：g07rc01
absolute maximum ratings (ta=25℃)
parameter		symbol		value				unit
forward current		if		20				ma
reverse voltage		vr		5				v
power dissipation		pd		80				mw
soldering temperature		tsol		260(for 5 seconds)				℃
operating temperature range		top		-25~+80				℃
storage temperature range		tstg		-30~+80				℃
peak pulsing current （1/8 duty f=1khz）		ifp		130				ma
electrostatic discharge		esd		>3000				v
electr-optical characteristics(ta=25℃,if=50ma)
parameter	test condition		symbol		value				unit
					min	typ	max
walvelenth	if=30ma		λd		620	---	630		nm
forward voltage	if=30ma		vf		1.8	---	2.4		v
luminous intensity	if=30ma		iv		600	---	800		mcd
luminous flux	if=30ma		φ		3.0	---	4.0		lm
viewing angle at 50% iv	if=30ma		2θ1/2		---	140	---		deg
reverse current	vr=5v		ir		---	5	---		μa

part number：g07rc01

●typical electro-optical characteristics curves

● reliability test items and conditions:

no.	test item	test condition	sample size	ac/re
1	dc operation life	if=dc20ma temp:room temperature test time:1000hrs	22	0/1
2	hight temperature hight humidity	temp.:+85℃ rh=85%hr test time:1000hrs	22	0/1
3	thermal shock	-35℃---~---+85℃ 20min 10s 20min test time:300cycles	22	0/1
4	hight temperature storage	hight temp.:+85℃ test time:1000hrs	22	0/1
5	low temperature storage	low temp.:-35℃ test time:1000hrs	22	0/1
6	temperature cycle	-35℃---~---+100℃ 15min 5min 15min test time:300cycles	22	0/1
7	reflow soldering	operation heating: 260℃(max.) within 10seconds(max.)	22	0/1

● judgement criteria of failure for the reliability

※ iv:below 50% of the initial value

※ vf:over 20% of the upper limit value

※ ir:over 2 times of the upper limit value

note:measurement should be taken between 2 hours and after the test leds have been returned to

normal ambient condition after completion of each test.

part number：g07rc01

● precautions for use:

1. temperature in use

since the light generated inside the led needs to be emitted to outside efficiently , a resin with hight light transparency is used, therefore, additives to improve the heat resistance or moisture resistance(silica gel,etc) which are used for semiconductors products such as transistors cannot be added to the resin.

consequently, the heat resistant ability of the resin used for led is usually low,therefore, please be careful of the following points:

avoid applying external force,stress and excessive vibration to the resins and terminals at hight temperature. the glass transition temperature of epoxy resin ussed for the led is approximately 120-130℃. if the temperature exceeding the limit,the coefficient of liner expansion of the resin doubles or more compared to that at normal temperature and the resin will be softened.

and if some external force or stress is applied at that time, it may cause a wire damage.

2. soldering

after soldering,avoided applying external force,stress and excessive vibration until the products down to the room temperature(the same to termial leads).

3. designing

care must be taken to provide the current limiting resistor in the circuit so as to drive the led within the rated figures, also caution should be taken not to overload led with exorbitant voltage at the turning on and off of the circuit.

when using the pulse drive care must be taken to keep the average current withini the rated figures, also the circuit should be designed so as be subjected to reverse voltage when turning off the led.

4. storage

in order to avoid the absorption of moisture, it is recommended to solder led as soon as possible after unpacking the sealed bags.

5. anti-static electricity

as the blue, green, white and puples are sensitive to the esd, so during the handling, soldering , testing and packing process the anti-static measurements must be applied.otherwise the led will be damaged.