热水自动增压泵H12GR-10

温岭韩程泵业有限公司成立于1995年.本厂主要生产韩程phc全自动冷热水自吸泵、非自动冷热水自吸泵、冷热水循环管道泵、热水自动增压泵、全自动家用增压泵等家用水泵，主要用于锅炉、壁挂炉、蒸气发生器、地暖循环设备等。

安装尺寸

性能曲线

增压泵的用途：
增压泵的用途主要有热水器增压用、高楼低水压、桑拿浴、洗浴等加压用、公寓Zui上层水压不足的加压、太阳能自动增压用等等。种类繁多，有家用增压泵、管道增压泵、消防增压泵、气动增压泵、气液增压泵等等。

booster pump uses:
the main purposes booster pump water heater with tall low pressure, turbo, sauna, bathing in the apartment, pressurized water pressure, lack of energy with automatic pressurization etc. phyletic, household booster pump and pipeline, pneumatic booster pump, fire booster pump, hydraulic booster pump booster pump etc.

增压泵的工作原理：
　　先将增压泵内充满液体，然后启动离心泵，叶轮快速转动，叶轮的叶片驱使液体转动，液体转动时依靠惯性向叶轮外缘流去，同时叶轮从吸入室吸进液体，在这一过程中，叶轮中的液体绕流叶片，在绕流运动中液体作用一升力于叶片，反过来叶片以一个与此升力大小相等、方向相反的力作用于液体，这个力对液体做功，使液体得到能量而流出叶轮，这时液体的动能与压能均增大。
　　气液增压泵工作原理类似于压力增压器，对大径空气驱动活塞施加一个很低的压力，当此压力作用于一个小面积活塞上时，产生一个高压。通过一个二位五通气控换向阀，增压泵能够实现连续运行。由单向阀控制的高压柱塞不断的将液体排出，增压泵的出口压力大小与空气驱动压力有关。当驱动部分和输出液体部分之间的压力达到平衡时，增压泵会停止运行，不再消耗空气。当输出压力下降或空气驱动压力增加时，增压泵会自动启动运行，直到再次达到压力平衡后自动停止。采用单气控非平衡气体分配阀来实现泵的自动往复运动，泵体气驱部分采用铝合金制造。接液部分根据介质不同选用碳钢或不锈钢，泵的全套密封件均为进口优质产品，从而保证了德科气液增压泵的性能。一般泵都有进气、排气两个口，在进气口能产生低于常压（即大气压）气压的叫“负压”；在排气口能产生高于常压气压的叫“正压”；比如常说的真空泵就是负压泵，增压泵就是正压泵。正压泵跟负压泵有很大的不同。比如气体流向，负压泵是外部气体被吸入到抽气嘴；正压是从排气嘴喷出去；比如气压的高低等。

the booster pump working principle:
first, then filled with liquid within the booster pump impeller start centrifugal pump impeller, fast, the leaf driven, liquid rotation inertia to rely on liquid outer impeller, while impeller to flow from the absorption in liquid, in this process, the impeller blades, the liquid flow around the liquid flow movement in a lift in leaf, role in the lift to a blade with equal and opposite forces, the power used for liquid of liquid work, make the liquid to get the energy and flow, liquid kinetic energy of impeller with pressure will increase.
gas-liquid booster pump working principle is similar to that of large diameter supercharger pressure air piston exerts a low pressure, when the pressure in a small area of the piston, produce a high pressure. through a two five ventilation control reversing valves, booster pump can achieve continuous running. the voltage controlled by fitting the plunger constantly liquid discharge, booster pump outlet pressure and air pressure on driving size. when the driver and output of liquid pressure balance, booster pump will stop running, no longer consumes air. when the output pressure drop or air pressure increases, the booster pump will start automatically run until you reach the pressure balance again after automatically stop. the single breath control non-e gas distributing valve to realize automatic reciprocating motion of the pump, the pump body part adopts gas driving aluminium alloy manufacture. according to the different media pick liquid part of carbon steel or stainless steel pump seals are set for imported high products, so as to ensure the performance of gas and liquid booster pump deco. general pump intake and exhaust are two mouth, in the intake can produce under normal atmospheric pressure (pressure); called "," in vent can produce higher atmospheric pressure is called ";" as the vacuum pressure is often said, booster pump is positive pressure pump pump. positive pressure pump suction pump with has the very big difference. such as gas flow pressure pump is external, gas is inhaled to smoke gas mouth, positive pressure from the exhaust mouth gush out, such as pressure level, etc.