厂家供应NABZC全自动变比组别测试仪

更新时间:2024-05-06 09:05:31 信息编号:4865371 发布者IP:27.18.205.109 浏览:47次
供应商
南澳电气(武汉)有限公司 商铺
认证
资质核验:
已通过营业执照认证
入驻顺企:
9
主体名称:
南澳电气(武汉)有限公司
组织机构代码:
91420100MA4KLYTB4P
报价
人民币¥10.00元每台
品牌
南澳电气(武汉)有限公司
型号
NABZC
生产厂家
南澳电气
关键词
变压器变比组别测试仪,变压器双臂电桥,全自动变比组别测试仪
所在地
武汉市东湖高新技术开发区光谷大道60号光谷科技产业园8栋
联系电话
027-87677658
手机号
15327206266
市场部专员
刘志新  请说明来自顺企网,优惠更多
让卖家联系我

产品详细介绍

 产品简介

用变比电桥测量变压器的变比,操作过程繁琐、测量范围狭窄,已经不适应现代测量快节奏、效率高的要求。为此,南澳电气(武汉)有限公司采用现代电子技术,研制出了新一代全自动变比组别测试仪。它体积小,重量轻,精度高,稳定性好。它采用了大屏幕中英文液晶屏显示、内置中英文菜单式操作,完成一组变压器的测试只需11秒。NABZC全自动变比组别测试仪是电力工业部门的理想测试仪器。

产品别名

变压器变比组别测试仪、变压器双臂电桥

产品特性

1.自动测量接线组别。

2.自动进行组别变换。

3.自动切换相序。

4.自动切换量程。

5.自动校表。

6.输入标准变比后,能自动计算出相对误差。

7. 一次测量完成,自动切断试验电压 。

8. 设置数据,测量结果自动保存,可查看以前数据。

9. 测量有载变压器,只输入一次变比。

产品参数

1.变比测量范围: 1—10000

2.组别:1—12点

3.精度: 1-1000 0.2 级 1000-10000 0.5级

4.电源:AC220V ±10%,50HZ

5.使用环境温度:-5℃ ─ 40℃

6.使用环境湿度:<85%

7.体积:430mm×320mm×215mm

8.重量:8Kg

 615874204.jpg

注意事项

1. 保险1为2A,保险2为0.5A。如果测试线短路,高低压接反,会熔断保险。保险熔断后,如果进行测量,在显示“ 正在测量,请等待! ”后停住。请关机,更换相同容量的保险,重测。

2.连线要保持接触良好。仪器应良好接地!

3.仪器的工作场所应远离强电场、强磁场、高频设备。供电电源干扰越小越好,宜选用照明线,如果电源干扰还是较大,可以由交流净化电源给仪器供电。交流净化电源的容量大于200VA即可。

4.仪器工作时,如果出现液晶屏显示紊乱,按所有按键均无响应,或者测量值与实际值相差很远,请按复位键,或者关掉电源,再重新操作。

5.显示器没有字符显示,或颜色很淡,请调节亮度电位器至合适位置。

亮度电位器是多圈电位器 ,有10圈!

6.仪器应存放在干燥通风处,如果长期不用或环境潮湿,使用前应加长预热时间,去除潮气。

7.通讯口调试时使用。

 

Product introduction

When using this radio bridge to measure the transformer ratio, the operation procedure is complex, the measuring measure range is narrow, which is no longer meet modern fast-paced, high-efficiency requirements. Therefore, NABZC electrical uses the modern electronic technology, developed a new generation of automatic variable ratio group tester. It is small, light, high accuracy and with good stability. It uses a large-screen character display, menu operation, friendly interface. The variable group can measure at once. NABZC Automatic variable ratio group tester is ideal product for electrical industry department.

Also called name

Transformer ratio group tester, transformer ratio tester, transformer ratio automatic tester, automatic transformer ratio tester, transformer ratio group testing device, transformer ratio testing device, transformer ratio automatic testing device.

The Characteristics of the products

1. Automatic measurement wiring group.

2. Automatic group transformation.

3. Automatic switching phase sequence.

4. Automatic shift ranging.

5. Automatic calibration.

6. Input the standard ratio, it can automatically calculate the relative error.

7.When the measurement is completed, it can cut off the testing voltage automatically .

8. Setting the data, the measured results can be saved automatically, and can be view the previous data.

9. Measuring loaded transformer ratio, only need to enter once

The parameters of the products

1. Ratio measuring range: 1-10000

2. Group:1-12:00

3. Accuracy: 1-1000  0.2 grade,1000-10000 0.5 grade

4. Power supply: AC220V ± 10%, 50HZ

5. Operating temperature: -5 ℃ ─ 40 ℃

6. Operating humidity:<85%

7. Volume: 430mm × 320mm × 215mm

8. Weight: 8Kg

Power supply: AC110V/115V/120V/127V/220V/230V/240V optional

Input frequency: 50Hz/60Hz optional

Note: The users can select the corresponding power which based on their local supply voltage and frequency, and we will confirm it before the delivery (or inform us that the goods will be used in which country advance)

Attentions should take

1.Insurance 1 is 2A, Insurance 2 is 0.5A. If the testing line is short-circuit , the high and low voltage will be reversed, will burn the fuse. Once fused, it will be displayed " measuring , wait ! " and then stop to operate and cut off the power.Please replace the same capacity insurance, then retesting .

2.Maintain the connections is fine. The instrument should be well grounded !

3.Ensure the workplace keep away from strong electric field , magnetic field and high-frequency devices. Power supply interference should be the smaller the better, and use light line. If the power supply interference is still large, it better to use the AC purified power,.the purified AC power supply capacity just larger than 200VA will do.

4.During the operating, if there is disorder on LCD screen, and without any response after press all the button, or the measured value is much very far away from the actual value, please press the reset button, or turn off the power, then restart the operate .

5.If the displays without character display ,or the color is weak, please adjust the brightness potentiometer to the appropriate location . Brightness potentiometer is a multi-turn potentiometer with 10 laps !

6.The instrument should be stored in dry and ventilated place , if unused for a  long-term, or stored in a humid environment, it need to extend the warm-up time before using , to remove  the moisture.

7.Communication port used for debugging .

相关产品:变压器变比组别测试仪 , 变压器双臂电桥 , 全自动变比组别测试仪
所属分类:中国仪表网 / 其他专用仪器仪表
本页链接:http://product.11467.com/info/4865371.htm
厂家供应NABZC全自动变比组别测试仪的文档下载: PDF DOC TXT
关于南澳电气(武汉)有限公司商铺首页 | 更多产品 | 联系方式 | 黄页介绍
主要经营:局部放电测试设备、高压试验变压器、高电压成套测量设备、高电压检测仪器、电缆和避雷器测试设备、微机继电保护测试设备、高精度分压器、接地和绝缘检测仪等
南澳电气(武汉)有限公司(简称“南澳电气”),主要从事电力检测设备、高电压试验研究、电力在线监测系统的研发,是早期国企改革后成立最早的创新型重点生产单位之一,公司是集研发、设计和制造高电压输变电检测设 ...
相关文章
我们的其他产品
顺企网 | 公司 | 黄页 | 产品 | 采购 | 资讯 | 免费注册 轻松建站
免责声明:本站信息由企业自行发布,本站完全免费,交易请核实资质,谨防诈骗,如有侵权请联系我们   法律声明  联系顺企网
© 11467.com 顺企网 版权所有
ICP备案: 粤B2-20160116 / 粤ICP备12079258号 / 粤公网安备 44030702000007号 / 互联网药品信息许可证:(粤)—经营性—2023—0112