提供沙特SABIC，PC,PC0703R，代理

 重庆市红蚂蚁塑业有限公司
联系人：潘银洁
手机 ：13883606760
电话 ；023-68689303
传真 ；023-68689302
QQ ；1157564052
E-mail；1157564052@qq.com
网址 ；www.21spc.net
地址 ；重庆市九龙坡区西彭镇西南国际塑料城13幢附16号
主营业务：【经营业务】
通用塑胶原料：ABS、PP、PS
工程塑胶原料：PC、PC/ABS、POM、PBT、PA6、PA66、PPA

主要品牌：
德国道默,上海聚威，SABIC，台湾南亚，台湾长春，韩国可隆，浙江俊尔


SABIC? PC Resin PC0703R

Asia Pacific: COMMERCIAL




PC0703R resin is a low flow (MFR = 7 at 300?C/1.2kg), heat and UV stabilized, polycarbonate product with mold release designed for use in the extrusion

market. It is available exclusively at www.sabicpc.com

TYPICAL PROPERTIES? TYPICAL VALUE Unit Standard

MECHANICAL
Tensile Stress, yld, Type I, 50 mm/min 63 MPa ASTM D 638
Tensile Strain, yld, Type I, 50 mm/min 6 % ASTM D 638
Tensile Strain, brk, Type I, 50 mm/min >70 % ASTM D 638
Tensile Modulus, 50 mm/min 2350 MPa ASTM D 638
Flexural Stress, yld, 1.3 mm/min, 50 mm span 90 MPa ASTM D 790
Flexural Modulus, 1.3 mm/min, 50 mm span 2300 MPa ASTM D 790
Hardness, Rockwell R 120 - ASTM D 785
Tensile Stress, yield, 50 mm/min 63 MPa ISO 527
Tensile Strain, yield, 50 mm/min 6 % ISO 527
Tensile Strain, break, 50 mm/min >70 % ISO 527
Tensile Modulus, 1 mm/min 2350 MPa ISO 527
Flexural Stress, yield, 2 mm/min 90 MPa ISO 178
Flexural Modulus, 2 mm/min 2300 MPa ISO 178
Hardness, Rockwell R 120 - ISO 2039-2
IMPACT
Izod Impact, unnotched, 23°C NB J/m ASTM D 4812
Izod Impact, notched, 23°C 900 J/m ASTM D 256
Instrumented Impact Energy @ peak, 23°C 65 J ASTM D 3763
Izod Impact, unnotched 80*10*3 +23°C NB kJ/m? ISO 180/1U
Izod Impact, unnotched 80*10*3 -30°C NB kJ/m? ISO 180/1U
Izod Impact, notched 80*10*3 +23°C 70 kJ/m? ISO 180/1A
Izod Impact, notched 80*10*3 -30°C 12 kJ/m? ISO 180/1A










(1) Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23°C/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.

Source GMD, last updated:

Visit www.sabicpc.com for additional information about SABIC? PC resins.









(2)Only typical data for selection purposes. Not to be used for part or tool design.
(3)This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
(4)Internal measurements according to UL standards.
(5)Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.

(6)Needs hard coat to consistently pass 60 sec Vertical Burn.


DISCLAIMER : THE MATERIALS, PRODUCTS AND SERVICES OF SAUDI BASIC INDUSTRIES CORPORATION (SABIC) OR ITS SIDIARIES OR AFFILIATES ( SELLER ) ARE SOLD SUBJECT TO SELLER S STANDARD

CONDITIONS OF SALE, WHICH ARE AVAILABLE UPON REQUEST. INFORMATION AND RECOMMENDATIONS CONTAINED IN THIS DOCUMENT ARE GIVEN IN GOOD FAITH. HOWEVER, SELLER MAKES NO EXPRESS OR IMPLIED REPRESENTATION, WARRANTY OR GUARANTEE (i) THAT ANY RESULTS DESCRIBED IN THIS DOCUMENT WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE
EFFECTIVENESS OR SAFETY OF ANY DESIGN OR APPLICATION INCORPORATING SELLER S MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS. UNLESS OTHERWISE PROVIDED IN SELLER S
STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS DESCRIBED IN THIS DOCUMENT.Each user is responsible for making its own determination as to the suitability of Seller s materials, products, services or recommendations for the user s particular use through appropriate end-use and other testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller s Standard Conditions of Sale or this Disclaimer, unless it is specifically agreed to in a writing signed by Seller. Statements by Seller concerning a possible use of any material, product, service or design do not, are not intended to, and should not be construed to grant any license under any patent or other intellectual property right of Seller or as a recommendation for the use of any material, product, service or design in a manner that infringes any patent or other intellectual property right.

SABIC and brands marked with ? are trademarks of SABIC or its subsidiaries or affiliates.

? 2016 Saudi Basic Industries Corporation (SABIC).