供应3x6大侧按卧式轻触开关带方形弹片

A.1
名称Project
常温…………………………………5℃～35℃
Normal temperature………………5℃～35℃
This specification is applied to the re for TACTILE SWITCH (MECHANICAL CONTACT)
APPLICATION
此规格书适用于机械式轻触开关的相关要求
4、 测试条件
Unless otherwise specified, tests and measurement shall be made in
the following standard conditions:
Test Conditions
在没有其它特定的条件下，应该在以下的条件下进行测试和测量：
环境气压…………………………86KPa～106Kpa
在制造过程中，测试和测量应该在以下的条件下进行：
If any doubt arise from the judgment, tests shall be conducted
at the following conditions:
温度…………………………………20℃±2℃
Temperature………………………20℃±2℃
相对湿度……………………………65%±5%
Relative humidity………………65%±5%
标准湿度……………………………相对湿度25%～85%
Normal humidity…………………relative humidity 25%～85%
标准大气压…………………………86KPa～106Kpa
Normal air pressure…………………86Kpa～106Kpa
Air pressure…………………………86KPa～106Kpa
2、 工作温度范围
Operating Temperature Range
－20℃～70℃(在标准大气压、标准湿度条件下)
-20℃～70℃（Normal humidity, normal air pressure）
3、 贮藏温度范围
Storage Temperature Range
-30℃～80℃(在标准大气压、标准湿度条件下)
-30℃～80℃（Normal humidity, normal air pressure）

5.4 开关结构：单回路单输出(具体的触点结构在装配图中已绘出)；
5.2 结构尺寸和安装尺寸：应符合装配图要求
Style and dimension: shall conform to the assemble drawings.
5.3 操作形式：有触觉反应的操作
 Type of actuating: Tactile feedback.
5、 详细说明
Detailed specification
5.1 外观：应无影响、降低产品性能的缺陷；
Appearance: There should be no defects that affect the serviceability of product
   Contact arrangement: 1 pole, 1 throw
   (Details of contact arrangement are given in the assembly drawings.)
5.5 开关工作额定值：DC 12V，50mA（有效值）
   Ratings: 12V DC, 50mA (effective value)
6、性能特征/Performance and characteristics
   ELECTRICAL SPECIFICATION
判定标准/Judgment
试验条件
TEST CONDITIONS
项目
ITEM
NO.
无击穿、无飞弧
There should be no
breakdown and
flashover
在以 5V 10mA的直流电源或不低于1KHz的交
流电源的电路中，以一个等于2倍按力的静负
荷施加于手柄中心
Applying a static load of 2 times
operating force to the center of the
stem, measurements shall be made by 5V
DC 10mA or more than 1KHZ AC smallcurrent
contact resistance meter.
在端子之间施加DC 100V /1min的条件下,测量
端子之间底座、盖板的电阻值
Measurement shall be made following
application of 100V DC potential, across
terminals, and across terminals and
cover, for one minute.
在端子之间施加250V AC(50HZ或60HZ)/1min
250V AC (50HZ or 60HZ) shall be applied
across terminals, for one minute.
≤100mΩ
≥100MΩ
介质耐压
Dielectric
voltage proof
6.3
6.2
6.1
接触电阻
Contact
Resistance
绝缘电阻
Insulation
Resistanc

8. 回流焊温度：
Reflow Temperature :

9.使用注意事项说明/Matters to be paid attention to when using motor
(1)进行焊接过程中，不可以用溶剂或类似品清洗开关
Following the soldering process,do not try to clean the switch with a solvent or
the like.
(2)注意不要施加超负荷的压力或晃动开关。
Please be cautions not to give excessive static load or shock to swiches.
（3）防止助焊剂从开关的顶端渗入
Safeguard the switch assembly against flux penetration from its topside.
交货后保证开关处于封密状态并库存时间90天以上
(4) Please have the products keep in close status and the storage time is 90
days guaranty after delivering the goods at most.