BTU 八温区空气炉SMT回流焊
信息编号：1386955 浏览：290次
- 供应商
- 北京科信拓达科技有限公司 商铺
- 认证
- 报价
- 请来电询价
- 品牌
- BTU
- 型号
- PYRAMAX98A
- 用途
- 回流焊工艺
- 所在地
- 北京市大兴区庞各庄镇瓜乡路32号院1号楼3层310号
- 联系电话
- 89282279
- 联系人
- 焦玲 请说明来自顺企网，优惠更多
- 让卖家联系我
产品详细介绍
| 品牌 | BTU | 型号 | PYRAMAX 98A |
| 用途 | 回流焊工艺 |
a.general specifications
|
maximum temperature rating: |
350°c |
|
|
nominal operating temperature: |
80-325°c |
|
|
number of controlled heated zones: |
7 top |
7 bottom |
|
oven atmosphere: |
air |
|
|
working dimensions: |
||
|
conveyor belt |
18 in. |
457 mm |
|
product clearance |
2 in. |
51 mm |
b.dimensional layout
| description |
inches |
centimeters |
|
onload area |
5 |
12.7 |
|
entrance, lip vent exhaust |
8 |
20.5 |
|
zone 1 |
14 |
35.6 |
|
zone 2 |
14 |
35.6 |
|
zone 3 |
14 |
35.6 |
|
zone 4 |
14 |
35.6 |
|
zone 5 |
14 |
35.6 |
|
zone 6 |
14 |
35.6 |
|
zone 7 |
14 |
35.6 |
|
total heated length |
98 |
248.9 |
|
exit, lip vent exhaust |
8 |
20.5 |
|
fan cooling |
22 |
55.9 |
|
offload area |
6 |
15.2 |
|
total system length |
147 |
373.4 |
|
total system width |
60 |
152.4 |
|
total system height (assumes 36” hearth line) |
60 |
152.4 |
c.process chamber
heating section § § § § §the process chamber is a clamshell design and includes the capability to process large format printed circuit boards up to 18 x 24 inches (457mm x 610mm). 24 x 24 inch (610mm x 610mm) board capability is available as an option § §zone to zone temperature isolation is greater than 600c § cooling section §d.conveyor system
|
conveyor belt |
||
|
belt width |
18 in. |
45.4 cm |
|
material |
302 stainless steel flat flex |
|
|
conveyorspeed range |
10 - 60 in/min. |
25.4 – 152.4 cm/min. |
|
conveyor speed nominal |
32 in/min. |
81.3 cm/min. |
|
product clearance |
2 in. (3 in. optional) |
51 mm (76 mm optional) |
|
drive motor |
1/16 hp / brushless dc |
|
|
conveyor height from floor |
33 - 39 in. |
839 - 991 mm |
| rail edge conveyor (optional) | ||
|
material |
#35 steel roller chain |
|
|
width |
2 – 18 in. |
5.1 - 45.7 cm |
|
support pin length |
0.187 in. (std) 0.375 in. |
4.7 mm (std) 9.5 mm |
|
pin to pin distance |
0.375 in. |
9.5 mm |
|
support pin height (clearances) |
1.2 in. above pin 0.8 in. below pin |
30.5 mm above pin 20.3 mm below pin |
|
rail parallelism |
0.040 in. |
1.0 mm |
|
rail height from floor |
33.8 in. – 39.8 in. |
859 mm – 1011 mm |
e.oven controls
temperature control §temperature control is accomplished by fourteen (14) pid control loops of the oven control unit (microprocessor) and windowsôwinconätemperature control accuracy is + / - .5° §ä §process over temperature protection is accomplished via winconä §redundant over temperature protection operator interface § § §ä §ä § § §f.atmosphere system
g.utility re(electrical power based on std. heater config. see installation drawing for final power)
|
voltage |
startup power |
operating power |
|
208 3æ/ 3 wire |
55 kw |
11-17 kw |
|
220 3æ/ 3 wire |
62 kw |
13-19 kw |
|
230 3æ/ 3 wire |
67 kw |
14-20 kw |
|
240 3æ/ 3 wire |
73 kw |
15-21 kw |
|
440 3æ/ 3 wire |
62 kw |
13-19 kw |
|
480 3æ/ 3 wire (std) |
73 kw |
15-21 kw |
|
380/220 3æ/ 4 wire |
62 kw |
13-19 kw |
|
400/230æ/ 4 wire |
67 kw |
14-20 kw |
|
415/240 3æ/ 4 wire |
73 kw |
15-21 kw |
|
utility |
supply pressure |
maximum flow rate |
|
exhaust entrance |
0.1 - .05 iwc |
300 ft3/min / 8.5 m3/min |
|
exhaust exit |
0.1 - .05 iwc |
300 ft3/min / 8.5 m3/min |
(note: consult final installation drawing for precise specifications. this is to be used a guide)
§ä §standard color: pillar white § §h.physical characteristics
crate: 4,300 lbs. / 1,955 kg
i.documentation
§ §user documentation §maintenance documentation §troubleshooting and repair documentation with easy part identification §1 hard copy manual
热风回流焊炉 BTU Pyramax品牌：BTU- 磨料磨削磨具研究所砂轮 现货样品或现货：现货
- 十温区空气回流焊炉 BTU品牌：BTU
- 十温区氮气回流炉 BTU品牌：BTU
- SD卡座 Molex莫莱克斯8.00元/个
品牌：Molex莫莱克斯 - 美国BTU十温区回流焊炉品牌：BTU
- 美国BTU八温区回流焊炉品牌：BTU
- 美国七温区回流焊炉 BTU品牌：BTU
- 国产GKG锡膏印刷机 GKG品牌：GKG
- GKG贴片加工丝印机GKG-G5型品牌：GKG
