自行车码表BYCICLE COMPUTER INSTRUCTIONS
信息编号:1314545 浏览:485次- 供应商
- 宁波剑创电子有限公司 商铺
- 认证
- 报价
- 人民币¥11.00元每件
- 品牌
- TOPSHING
- 类型
- 电子
- 材质
- ABS
- 所在地
- 江北区北海路188弄65号(注册地址)
- 联系电话
- 86 574 88195992/88195589
- 手机号
- 15867518920
- 联系人
- 石丽丽 请说明来自顺企网,优惠更多
- 让卖家联系我
产品详细介绍
品牌 | TOPSHING | 类型 | 电子 |
材质 | ABS | 是否防水 | 是 |
是否带暂停 | 否 | 是否防滑 | 是 |
bycicle computer instructions
14 functions
●spd current speed
●odo odometer(total distance)
●dst trip distance
●mxs maximum speed
●avs average speed
●tm elapsed time
●r rotation per minute
●clock(24h)
●scan
●“▲” “▼” comparator
●setting speed scale(km/h, m/h)
●setting tyre circumference(10cm~239cm)
●setting the last value of odometer(km or m)
●auto on/off
battery installation
remove the battery cover from the bottom of the computer using a flat blade screwdriver. install a ag13 battery with the positive(+) pole facing the battery cover and replace the cover. should the lcd show irregular figures or have no shows, take out the battery and install again.
notes: when install the battery, please don’t make any spring contact tongue out of shape.(the battery positive connecting sheet have three spring contact tongues)
speedometer sensor
the speedometer sensor bracket attaches to the left fork blade.
using rubber shims to adjust to the diameter of the fork. position
the sensor and magnet as show, making sure the arc of the
magnet intersects the alignment mark on the sensor with the
clearance less than 5mm.
the magnet attaches to the front wheel spoke with the screws
provided
mounting shoe
attach the mounting shoe to the
handlebar using the bracket
screw provided. rubber shims
are also included to provide a
secure fit if the clamp can’t
close completely, or the
bracket slips on the handlebar, shims will be necessary.
bracket can be attached to either left or right hand side of the
handlebar
sensor wiring
route the sensor wire up the fork blade, using tie wraps to secure
it at the bottom and crown. wire must nit hang loosely. leaving
enough slack to allow free movement of the front wheel. route
the remaining wire around the front brake cable and to the
handlebar. excess wire should be carefully looped and secured to
the stem with a tie wrap.
computer
the computer attaches to the
mounting shoe by sliding the unit
until it snaps firmly into position.
push forward the opposite
direction to remove.
to check for proper speed
function and sensor alignment.
spin the front wheel with
computer in speed mode. adjust
the position of sensor and magnet when there is no or weak reactivity.
km/mile selection
after installing the battery within 15 seconds (it enters automatic
cycle after 15 seconds), the mainframe display km/h;press left
button to choose km/h or m/h. range of speed recording:
0~99.9km(m)/h.
→press right button to enter wheel size input mode
wheel size input
the mainframe display 3 flickering number, choose needed perimeter according to the following diagram, press left button to input (for example: input the number by pressing left button for over 2 second), the circumference varies between 10cm~239cm, default mainframe display is 208cm.
tyre type(diameter) |
tyre circumference |
20” |
160 |
22” |
176 |
24” |
192 |
26”(650a) |
207 |
26.5”(tubular) |
211 |
26.6”(700x25c) |
212 |
26.8”(700x28c) |
214 |
27”(700x32c) |
216 |
28”(700b) |
224 |
(w/tyre) |
|
atb 24”x1.75 |
189 |
atb 26”x1.4 |
200 |
atb 26”x1.5 |
203 |
atb 26”x1.75 |
205 |
atb 26”x2(650b) |
210 |
27”x1 |
214 |
27”x1 1/4 |
216 |
→press right button to enter dst mode
setting the last value of odometer
the last value of the total distance (i.e. the figure 0000.0 on the right of the bottom of the screen) can be adjusted. (after reinstalling the battery, latest value can be input according to the value exists before the battery is reinstalled). press the left button to change the flickering digits, press the right button to change to the next digit. the default last value of the odometer is “0.0”. press the right button to skip any digit.
auto on/off
to preserve batteries, the cycle computer will automatically switch off if the unit is left unused for over 2 minutes. display will reappear with a press on either button or input from the sensor.
recording the cycle movements
press the righ button to enter dst mode, press the left button until “km” and “h” (or “m” and “h” ) of “km/h” (or “m/h” ) starts to flicker to record dst、mxs、avs and tm. when there is input from the sensor, “/” starts to flicker.
notes:▼the cycle movement can’t be recorded by odo and clock mode.
▼the cycle movement can be recorded just only by dst、mxs、avs、tm and r mode.
▼recording the cycle movements mode is opposite freeze frame memory mode, default mode is freeze frame memory.
→press the left button to enter freeze frame memory mode by dst、mxs、avs、tm and r mode.
freeze frame memory
press the left button, freeze frame memory can lock the display
at the end of a ride segment by dst、mxs、avs、tm and r mode,
“km” and “h” (or “m” and “h” ) of “km/h” (or “m/h” ) stops to flicker. the cycle movement ( dst、mxs、avs and tm mode) can be read at later time by pressing the right button. to release the memory, press the left and right button at the same time, the value of dst、mxs、avs and tm will be back to zero.
★that is particularly useful to record the information after finishing a sports competition.
speedometer
instantaneous speed is indicated on the top line. the rage of measurement is 0~99.9km/h (m/h) and accuracy is +/-0.1 km/h (m/h).
speed comparator (cadence)
during riding, “▲” indicants that the instant speed is higher than average speed(avs). “▼” indicants the instant speed is lower than the average speed.
odometer(odo)
mileage function mode: the mainframe appears the total distance after it is restored at the last time, press left button to know the fixed value of the tyre circle, press left button for 6 seconds to clear out all the odo value and other records and information, the user need to reset the km (m), tyre circle, and the original odo value, the clock will remain. total distance display 0~9999.9 km(m), the mainframe will be back to zero when value exceeds the maximum limit,
→press right button to enter dst mode.
trip distance(dst)
the distance for one trip indicated by dst is displayed on the bottom line.
reset dst by pressing the left and right button at the same time. the computer will clear the records of dst, mxs, avs and tm. dst ranges from 0~9999.9km(m), when the value exceeds the range, it restarts from 0 automatically.
→press the right button to mxs mode
maximum speed(mxs)
maximum speed measurement for one trip is indicated by mxs and is displayed on the bottom line.
→press the right button to enter avs mode
average speed(avs)
average speed measurement is indicated by avs and is displayed on the bottom line. avs is calculated with the trip time (tm), avs is the average speed only while riding.
→press the right button to enter tm mode
通用型无线码表
- cycle computer码表10.00元/件
品牌:doustone - hour meter 0(mL)25.00元/套
排量:0(mL) - 计时器 JT 3259229.00元/台
品牌:JT - 汽车胎压计 数显胎压计 JT511014.00元/个
类型:数显胎压计 - 计时器 JT 3259229.00元/台
品牌:JT - cycle computer自行车速度表10.00元/件
产品类别:码表 - 定时器80972LCD液晶屏品牌:DOUSTONE
- 制冰机31951LCD液晶屏品牌:DOUSTONE
- 淋浴房LCD209 1.1(mm)规格:60*120.*116(mm)
- 366供应温度计LCD doustone品牌:doustone