3.5插件耳机插座PJ-354
信息编号:2908583 浏览:102次- 供应商
- 东莞市韩晶电子有限公司 商铺
- 认证
- 报价
- 请来电询价
- 品牌
- HJ
- 型号
- PJ-354
- 所在地
- 东莞市桥头镇田新社区商业街60号
- 联系电话
- 13712896873
- 手机号
- 13751281893
- 经理
- 陈溪煌 请说明来自顺企网,优惠更多
- 让卖家联系我
产品详细介绍
designation品名:耳机插座 |
model型号: |
edition版本:01 |
page页码:1 of 2 |
||||
1.rationg额定值: |
dc 30v0.5a |
||||||
2.operation temperature range使用温度范围: |
-20~+70℃ |
||||||
3.preservative temperature range:保存温度范围: |
-40~+85℃ |
||||||
4.construction dimension结构尺寸: |
apply to the appended drawing: 符合附加图纸 |
||||||
item项目 |
test condition测试条件 |
spectification规格 |
|||||
5.electronical characteristics.电气性能. |
|||||||
5.1 |
contact resistance 接触阻抗 |
being measured at 1khz small current contact resistance meter. 在1khz小电流下测量. |
30mωmax 30毫欧以下. |
||||
5.2 |
insulation resistance 绝缘阻抗 |
measurements shall be made following application of dc500v potential across terminals and across terminals and frame for 1 minute. 在端子之间各端子与壳之间加dc500v条件下,持 续1分钟测量. |
100mωmin 100兆欧以上. |
||||
5.3 |
vithstand voltage 耐电压 |
ac 500v(50hz or 60hz)shall be applied across terminals and across terminals and frame for one minute 在端子之间各端子与壳之间加ac 500v(50hz或60hz)条件下,持续1分钟测量. |
there shall beno breakdown. 无异现象出现. |
||||
6.mechanical characteristics.机械性能. |
|||||||
6.1 |
insertion and withdraw force插拨力 |
being measure at across spring piece and across matching plug for ergometer 用测力计在插头与弹片之间进行测量. |
insertion and extraction force 3-25n 插拨力 3-25n |
||||
6.2 |
terminal strengith 端子强度 |
a static force of 500gf being applied in one direction on the tip of terminal for 1 minute. 一个500克之静负荷施加于端子顶部的一个方向持续1分钟. |
there shall be no sign of damage mechanically and electically. 无任何异象显示机械及电气性能之损环. |
||||
7.durability.耐久性. |
|||||||
7.1 |
soldering test. 可焊性试验 |
the tip of the terminals shall be dipped2mm in the solder bath at a temperature of 260±5℃ for 3±0.5℃sec. 端子顶部被浸入焊锡池2mm深,温度260±5℃时间3±0.5℃秒 |
a new uniform coacting of solder shall cover a minimum of 90 of the surface being immersed.浸入的部分90%以上表面将被锡覆盖. |
||||
7.2 |
resistance to soldering heat 耐焊接热 |
soldering area:t/2 of p.c.b thickness焊接面积:印刷 基板的1/2厚度处 temperature:260±5℃sinking time: 5±1s.焊接温度:260±5℃,焊接时间:5±1秒. |
no damage (electrical and mechanical) 无异常。(电气、机械特性) |
||||
designation品名:耳机插座 |
model型号:pj-327f |
edition版本:01 |
page页码:2 of 2 |
|||
item项目 |
test condition测试条件 |
spectification规格 |
||||
7.3 |
life test. 寿命试验 |
5,000 cycles of operation at r rate of 20-30 cycles per minute with unloading. 无负载条件下,每分钟20-30次的速度操作5,000次。 |
(1).contact resistance.40mωmax接触阻抗40毫欧以下. (2).insertion and withdraw force 30 initial value插拨力变化范围初始值30% (1).item 专案-5.2 (1).item 专案-5.3 (1).item 专案-6.2 |
|||
7.4 |
heat test. 耐热试验 |
85±2℃for 48 hours after test keep in normal condition for 30 minutes. 在85±2℃环境中放48小时,再放在正常环境中30分钟后进行测试. |
(1).contact resistance50mωmax.接触电阻50毫欧以下 (2).insulation resitance50mωmin 绝缘电阻50兆欧以上 (3).there shall be no sign of damage mechanically and electrically.无任何异象显示机械及电器性能之损环. |
|||
7.5 |
humidity test. 耐湿试验 |
the condition of temperature 40±2℃and humidty 90-95% for 48 hrs.after test keep in normal condition for 30 min. 在温度40±2℃,湿度90-95%环境中放48小时,再放在正常环境中30分钟后进行测试。 |
||||
7.6 |
cold test. 耐冷试验 |
at 5% nacl liquor for 24 hours,after washing,keep in normal condition for 30 min. 在-40±2℃,湿度90-95%环境中放48小时,再放在正常环境中30分钟后进行测试. |
||||
7.8 |
salt spray test 盐雾试验 |
at 5% nacl liquot for 24 hours,after washing,keep in normal condition for 30 min. 浸入5%的nacl溶液中24小时,用水清洗并在室温下放置30分钟. |
without excessive corrosion or crack in appearance 表面无明显腐蚀或裂纹 |
|||
8.standard condition试验、测定状态 |
||||||
unless otherwise specified,the test and measurements shall be carried out as follows: ambient temperature温度:5-35℃ relative humidity相对湿度:45-85% air pressurs气压:86-106kpa(860-1060mbar) however if doubt arises on the decision based on the measured values under the above-mentioned conditions,then following condition shall be employed:但在对判定产生异常时,按下述状能实施: ambient temperature温度:20±2℃ relative humidity相对湿度:65±5% air pressure气压:86-106kpa(860-1060mbar) |
本产品的加工定制是否,品牌是HJ,型号是PJ-354,额定电流是0.5(A),额定电压是30(V),环境温度是耐高温260度(℃),壳体材质是尼龙,PBT,LCP,ABS,导电体材质是磷铜,猛钢,产品认证是ROHS,REACH
- DC电源插座(SMT)DC-096D加工定制:否
- DC电源插座(SMT)DC-056加工定制:否
- 东莞韩晶 排针单排 弯排针 u型排针 90度排针保质品牌:韩晶
- 三档微型拨动开关 8脚贴片 MSK-07D加工定制:是
- 2.0mm间距 双排弯排针排母 双弯插针 双排贴片排针加工定制:是
- FPC卧贴翻盖,连接器FPC品牌:HANJING
- 白色排针排母 双排排母 长排母 可订做加工加工定制:是